Losses in the EoMPLS network?

Question

Computer networks

When using EoMPLS technology between L3 switches WS-C6504-E and ME-3600X-24FS-M, packet losses of 10-15% are observed when trying to reach the pppoe protocol (tried static IP) from the workstation to the border.
On 6504, a subinterface is configured towards the border, and on 3600, xconnect takes traffic from the vlan interface.
At the same time, MPLS traffic in the global table and vrf (L3VPN) goes without loss, the problem is in AToM traffic.
The network topology and configs are presented below.
Please help if anyone faced similar problem

Configs:

Cat 6504<br/>
<br/>
interface TenGigabitEthernet1/4<br/>
 mtu 8000<br/>
 ip address 10.76.0.106 255.255.255.252<br/>
 logging event link-status<br/>
 mpls mtu 1550<br/>
 mpls label protocol ldp<br/>
 mpls ip<br/>
<br/>
interface GigabitEthernet1/3.1111<br/>
 encapsulation dot1Q 1111<br/>
 xconnect 10.76.0.1 111 pw-class pppoe<br/>
<br/>
pseudowire-class pppoe<br/>
 encapsulation mpls<br/>
<br/>
sh mpls l2transport vc 111 det<br/>
Local interface: Gi1/3.1111 up, line protocol up, Eth VLAN 1111 up<br/>
 Interworking type is Ethernet<br/>
 Destination address: 10.76.0.1, VC ID: 111, VC status: up<br/>
 Output interface: Te1/4, imposed label stack {17}<br/>
 Preferred path: not configured <br/>
 Default path: active<br/>
 Next hop: 10.76.0.105<br/>
 Load Balance: none<br/>
 Flow Label: Disabled<br/>
 Create time: 05:13:22, last status change time: 05:13:21<br/>
 Signaling protocol: LDP, peer 10.76.0.1:0 up<br/>
 Targeted Hello: 10.76.0.2(LDP Id) -&gt; 10.76.0.1, LDP is UP<br/>
 Status TLV support (local/remote) : enabled/not supported<br/>
 LDP route watch : enabled<br/>
 Label/status state machine : established, LruRru<br/>
 Last local dataplane status rcvd: No fault<br/>
 Last local SSS circuit status rcvd: No fault<br/>
 Last local SSS circuit status sent: No fault<br/>
 Last local LDP TLV status sent: No fault<br/>
 Last remote LDP TLV status rcvd: Not sent<br/>
 Last remote LDP ADJ status rcvd: No fault<br/>
 MPLS VC labels: local 22, remote 17 <br/>
 Group ID: local 0, remote 0<br/>
 MTU: local 1550, remote 1550<br/>
 Remote interface description: <br/>
 Sequencing: receive disabled, send disabled<br/>
 Control Word: Off (configured: autosense)<br/>
 VC statistics:<br/>
 transit packet totals: receive 18896, send 22250<br/>
 transit byte totals: receive 11066229, send 17872490<br/>
 transit packet drops: receive 0, send 0<br/>

ME3600<br/>
<br/>
interface TenGigabitEthernet0/2<br/>
 port-type nni<br/>
 no switchport<br/>
 mtu 8000<br/>
 ip address 10.76.0.105 255.255.255.252<br/>
 mpls mtu 1550<br/>
 mpls label protocol ldp<br/>
 mpls ip<br/>
<br/>
interface Vlan1111<br/>
 mtu 1550<br/>
 no ip address<br/>
 xconnect 10.76.0.2 111 pw-class pppoe<br/>
end<br/>
<br/>
pseudowire-class pppoe<br/>
 encapsulation mpls<br/>
<br/>
Local interface: Vl1111 up, line protocol up, Eth VLAN 1111 up<br/>
 Interworking type is Ethernet<br/>
 Destination address: 10.76.0.2, VC ID: 111, VC status: up<br/>
 Output interface: Te0/2, imposed label stack {22}<br/>
 Preferred path: not configured <br/>
 Default path: active<br/>
 Next hop: 10.76.0.106<br/>
 Create time: 05:17:56, last status change time: 05:16:31<br/>
 Signaling protocol: LDP, peer 10.76.0.2:0 up<br/>
 Targeted Hello: 10.76.0.1(LDP Id) -&gt; 10.76.0.2<br/>
 Status TLV support (local/remote) : enabled/not supported<br/>
 Label/status state machine : established, LruRru<br/>
 Last local dataplane status rcvd: no fault<br/>
 Last local SSS circuit status rcvd: no fault<br/>
 Last local SSS circuit status sent: no fault<br/>
 Last local LDP TLV status sent: no fault<br/>
 Last remote LDP TLV status rcvd: not sent<br/>
 MPLS VC labels: local 17, remote 22 <br/>
 Group ID: local 0, remote 0<br/>
 MTU: local 1550, remote 1550<br/>
 Remote interface description: CN_10.76.0.2_Te1/3.1111 to BRAS<br/>
 Sequencing: receive disabled, send disabled<br/>
 VC statistics:<br/>
 packet totals: receive 22648, send 20967<br/>
 byte totals: receive 18187297, send 12609294<br/>
 packet drops: receive 0, send 0<br/>

Test

ping X.X.X.X rep 100<br/>
<br/>
Type escape sequence to abort.<br/>
!!!!!.!!!!!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!<br/>
!!!.!!!!!.!!!!!.!!!!!.!!!!!.!!<br/>
Success rate is 84 percent (84/100), round-trip min/avg/max = 1/1/31 ms<br/>
<br/>
ping X.X.X.X rep 100 si 1500<br/>
<br/>
Type escape sequence to abort.<br/>
!!.!!.!!.!!.!!.!!.!!.!!.!!.!!!!!!.!!!.!!.!!.!!.!!.!!.!!.!!.!!.!!.!!.!!<br/>
.!!.!!.!!.!!.!!.!!.!!.!!.!!.!!<br/>
Success rate is 69 percent (69/100), round-trip min/avg/max = 1/3/33 ms<br/>