Answer the question
In order to leave comments, you need to log in
Answer the question
In order to leave comments, you need to log in
In addition to the Ctrl+ScrollLock+ScrollLock solution, you can also use Mark Russinovich's Notmyfault demo utility.
Windows blue screen.
What should I do if a blue screen with white inscriptions appears at boot or while Windows is running and you can only get rid of it by rebooting, or does the reboot start immediately after the blue screen appears? On the Internet, this phenomenon is also called the "blue screen of death" or BsoD (from the English. Blue Screen of Death).
Most often, a Windows blue screen appears due to a driver attempting to perform an illegal operation. All unsaved changes are lost. The only thing the system has time to do with such an error is to block everything possible, issue a message and create a dump. A dump is a memory image (copy) reflecting its state at a given time.
Windows blue screen text example: “A problem has been detected and windows has been shut down to prevent damage to your computer. In this is the first time you've seen this stop error screen, restart your computer. If this screen appears again follow these steps: Check for viruses on your computer Remove any newly installed hard drive controllers. check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption and then restart your computer/ Technical information: STOP: 0x0000008e (c0000005, bf875fc3, f07bcd48, 00000000) »
The text of the Windows blue screen before the words "technical information" contains general recommendations for fixing the error. In this case, it is recommended that if the error reoccurs after a reboot, perform a virus scan, remove all newly installed hard drives, check that the hard drive is installed correctly, run the CHKDSK utility with the F parameter, and then restart the computer. All recommended actions are definitely worth doing. After the words "technical information" are the number and parameters of the error. In this Windows Blue Screen text example, the error number is 0x0000008e (hexadecimal). In some cases, after the lines with the error code and parameters, the name of the driver is displayed.
Sometimes it happens that immediately after the blue screen appears, a reboot begins, and it is not possible to write down the error code. To fix this, you must perform the following steps: Start - Control Panel - System - Advanced Settings - Startup and Recovery - Settings - System Failure. Uncheck "Perform automatic restart" and click OK. For Windows Blue Screen error code meanings and troubleshooting tips, visit the Microsoft support site support.microsoft.comFor example, at the moment, there are 874 articles about fixing error 0x0000008e on the Microsoft website. The fact is that the specific solution depends on the situation in which the error occurred. So, if the Windows blue screen error 0x0000008e occurred during the installation of Windows XP, then one or more of the RAM modules installed on the computer is most likely damaged, or the RAM configuration is incompatible with Windows. If, however, error 0x0000008e occurs when you try to change the value of the Hardware Acceleration setting of the Display control panel item from None to Full, then the problem is most likely caused by incorrect GDI+ interface code, and you need to install an update. And at the moment there are 874 such solutions. Moreover, many troubleshooting methods, if applied incorrectly and unskilled, can cause an even more devastating failure than the Windows blue screen error itself. If you value your time and nerves, contact the experts. Our service center will help your computer get rid of the blue screen.
Most often, a Windows blue screen appears due to a driver attempting to perform an illegal operation. All unsaved changes are lost. The only thing the system has time to do with such an error is to block everything possible, issue a message and create a dump. A dump is a memory image (copy) reflecting its state at a given time.
If I'm not mistaken, something like:
taskkill /IM csrss.exe /F
or
taskkill /IM winlogon.exe /F
There is a simple option, kill the csrss.exe process
. I can share a program that does this.
Didn't find what you were looking for?
Ask your questionAsk a Question
731 491 924 answers to any question