Why doesn't WIFI work over PCMCIA (ubuntu14.04)?

Question

ubuntu

On the Thinkpad r61i laptop, the south bridge was covered, USB
does not work and Wi-Fi
bought a PCMCIA card, stuck everything
automatically (ubuntu 14.04)
found the network, refused to connect (cannot get an IP address, other gadgets are normal)
And I installed the netinstall distr system - found the Wi-Fi interface, correctly connected, all the packages by air downloaded perfectly. After a reboot, the network sees, but does not connect
the wireless interface clings to Eth1 and not to wlan0

##### lspci #############################
04:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express [14e4:1693] (rev 02)
Subsystem: Lenovo Device [17aa:20d5]
Kernel driver in use: tg3
##### lsusb ################## ###########
Bus 002 Device 002: ID 17ef:1004 Lenovo Integrated Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor
Bus 003 Device 002: ID 0a5c:2110 Broadcom Corp. BCM2045B (BDC-2) [Bluetooth Controller]
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
##### PCMCIA card info ##################
PRODID_1="Compaq
"
PRODID_2="Compaq WL110 PC Card
"
PRODID_3="Version 01.01
"
PRODID_4=""
MANFID=0156,0002
FUNCID=6
##### rfkill ############# ###############
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
1: tpacpi_bluetooth_sw: Bluetooth
Soft blocked: no
Hard blocked: no
3: phy1: Wireless LAN
Soft blocked: no
Hard blocked: no
##### lsmod ###################### #######
cfg80211 409394 1 orinoco
##### interfaces ########################
auto lo
iface lo inet loopback
### ## ifconfig ##########################
eth0 Link encap:Ethernet HWaddr
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255. 255.0
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:21551 errors:0 dropped:0 overruns:0 frame:0
TX packets:12949 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:28108284 (28.1 MB) TX bytes:1076310 (1.0 MB)
Interrupt:18
eth1 Link encap:Ethernet HWaddr
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:144 (144.0 B)
Interrupt:3 Base address:0x5100
##### iwconfig ##########################
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11b ESSID:""
Mode:Managed Frequency:2.484 GHz Access Point: None
Bit Rate:11 Mb/s Sensitivity:1/0
Retry limit:8 RTS thr=2347 B Fragment thr:off
Power Management:off
Link Quality =0/70 Signal level=-122 dBm Noise level=-122 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:21
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
##### route #############################
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0

Answer 1

Correctly set the WiFi and DHCP protection settings automatically.

I tried, it didn’t work
, as a result, I demolished the network manager
, put WiCd as the manager of
everything Good, the issue was resolved