Is the patient more alive than dead (array problem)?

Question

linux

Everything was fine, calm. I drank tea and ate sweets. And then suddenly began to fill up the VM. Everything was buggy, the CPU was loaded at 100%. A gluttonous monster was found that ate all the CPU resources, vhost_net itself. Suspicion fell on the ride array. Gently, affectionately persuaded him to give the state of the array ...
The array is intact, but the temperature of the raid controller confused 63 degrees and this is without load (at a temperature in the server room no more than 20 degrees)

Controllers found: 1
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
      Device #0
         Device is a Hard drive
         State                              : Online
         Supported                          : Yes
         Transfer Speed                     : SATA 6.0 Gb/s
         Reported Channel,Device(T:L)       : 0,0(0:0)
         Reported Location                  : Enclosure 0, Slot 31
         Reported ESD(T:L)                  : 2,0(0:0)
         Vendor                             : WDC
         Model                              : WD1003FBYZ-010FB
         Firmware                           : 01.01V03
         Serial number                      : WD-WCAW37116428
         Size                               : 953869 MB
         Write Cache                        : Enabled (write-back)
         FRU                                : None
         S.M.A.R.T.                         : No
         S.M.A.R.T. warnings                : 0
         Power State                        : Full rpm
         Supported Power States             : Full rpm,Powered off,Reduced rpm
         NCQ status                         : Enabled
      Device #1
         Device is a Hard drive
         State                              : Online
         Supported                          : Yes
         Transfer Speed                     : SATA 6.0 Gb/s
         Reported Channel,Device(T:L)       : 0,1(1:0)
         Reported Location                  : Enclosure 0, Slot 30
         Reported ESD(T:L)                  : 2,0(0:0)
         Vendor                             : WDC
         Model                              : WD1003FBYZ-010FB
         Firmware                           : 01.01V03
         Serial number                      : WD-WCAW37116447
         Size                               : 953869 MB
         Write Cache                        : Enabled (write-back)
         FRU                                : None
         S.M.A.R.T.                         : No
         S.M.A.R.T. warnings                : 0
         Power State                        : Full rpm
         Supported Power States             : Full rpm,Powered off,Reduced rpm
         NCQ status                         : Enabled
(часть вывода отрезана из-за ограничения)    
<code>
Controllers found: 1
<SmartStats controllerID="0" time="1439467645" deviceVendor="Adaptec" deviceName="6805E" serialNumber="4A041350F4E">
<PhysicalDriveSmartStats channel="0" id="0" nonSpinning="false" isDescriptionAvailable="false" >
<Attribute id="0x01" normalizedCurrent="200" normalizedWorst="200" threshold="51" rawValue="0" />
<Attribute id="0x03" normalizedCurrent="174" normalizedWorst="174" threshold="21" rawValue="4266" />
<Attribute id="0x04" normalizedCurrent="100" normalizedWorst="100" threshold="0" rawValue="22" />
<Attribute id="0x05" normalizedCurrent="200" normalizedWorst="200" threshold="140" rawValue="0" />
<Attribute id="0x07" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="0" />
<Attribute id="0x09" normalizedCurrent="88" normalizedWorst="88" threshold="0" rawValue="9002" />
<Attribute id="0x0A" normalizedCurrent="100" normalizedWorst="253" threshold="0" rawValue="0" />
<Attribute id="0x0B" normalizedCurrent="100" normalizedWorst="253" threshold="0" rawValue="0" />
<Attribute id="0x0C" normalizedCurrent="100" normalizedWorst="100" threshold="0" rawValue="22" />
<Attribute id="0xC0" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="21" />
<Attribute id="0xC1" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="5" />
<Attribute id="0xC2" normalizedCurrent="108" normalizedWorst="98" threshold="0" rawValue="39" />
<Attribute id="0xC4" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="0" />
<Attribute id="0xC5" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="0" />
<Attribute id="0xC6" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="0" />
<Attribute id="0xC7" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="0" />
<Attribute id="0xC8" normalizedCurrent="200" normalizedWorst="200" threshold="0" rawValue="0" />
</PhysicalDriveSmartStats>

</SmartStats>
(часть вывода отрезана из-за ограничения)

</code>но увы не могу его разобрать, поэтому прошу понять и помочь разобраться это контроллер или диски, или каким способом можно снять адекватный смарт?

Answer 1

adapt? 63 degrees is a normal temperature for a processor. There, the varning starts at 80, as far as I remember...
What is the array?

Answer 2

Normal temperature, if you have someone loading disks, then the load is 100% on the controller, and after all, it has passive cooling, not active.