How to configure bridge over bonding in RHEL 6.4 Server?

Question

linux

There is an installed system ( rhel-server-6.4-x86_64-dvd.iso ). On top of which KVM is installed ( installation instructions ). The host machine and guest machine are assigned their own IP addresses, for this, according to the instructions from Habr, the br0 bridge is configured. Everything is working. Now we need to do bridge over bonding.
I put the following settings on the host:

[[email protected] ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 
DEVICE=eth0
HWADDR=f0:92:1c:0f:76:f8
MASTER=bond0
SLAVE=yes
ONBOOT=yes

[[email protected] ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
DEVICE=eth1
HWADDR=F0:92:1C:0F:76:FC
MASTER=bond0
SLAVE=yes
ONBOOT=yes

[[email protected] ~]# cat /etc/sysconfig/network-scripts/ifcfg-bond0 
DEVICE=bond0
ONBOOT=yes
BRIDGE="br0"

[[email protected] ~]# cat /etc/modprobe.conf 
alias bond0 bonding
options bond0 mode=1 miimon=100

[[email protected] ~]# cat /etc/sysconfig/network-scripts/ifcfg-br0 
DEVICE="br0"
NM_CONTROLLED="no"
ONBOOT="yes"
TYPE="Bridge"
BOOTPROTO="static"
IPADDR="10.2.26.39"
GATEWAY="10.2.26.1"
MTU="1500"
NETMASK="255.255.255.0"
DEFROUTE="yes"
IPV4_FAILURE_FATAL="yes"
IPV6INIT="no"
NAME="System br0"

Checking:

[[email protected] ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth0
MII Status: down
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:76:f8
Slave queue ID: 0

Slave Interface: eth1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:76:fc
Slave queue ID: 0

eth0 down. Although I expected to see something like the following:

[[email protected] ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth0
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:d5:e8
Slave queue ID: 0

Slave Interface: eth1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:d5:ec
Slave queue ID: 0

The question is actually in the subject, how to set up bridge over bonding in RHEL 6.4 Server?